$9.99 - $19.99
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Park Tool's Tool Tray Collar easily adapts the #106 Work Tray to fit the 41mm upright tube on 2011 and older PRS-20 and PRS-21 Repair Stands, as well as 1996 and newer PCS-1, PCS-4, PCS-4-1 and PCS-4-2 Repair Stands (each sold separately).
Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.
Park's Paper-Towel Holder is an accessory for Park's Professional Race Stand (sold separately). It attaches easily and holds a standard roll of paper towels. It also works great for hanging clothes, wheels and tires.
Park's Work Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools and small parts close at hand. It has deep sides so your small items stay put and many slots for holding your tools. The Tool Tray fits Park's PRS-2, PRS-3, PRS-6, PRS-11, PRS-12, PCS-1 and PCS-4 repair stands.
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease. - Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3 - Easily removed and installed with hook-and-loop material
Park Tool's Repair Kit features the most common replacement parts for the 100-3C and 100-5C clamps. Includes: • 118s adjusting barrel • 117s eyebolt • 121s adjusting barrel pivot • 136 nut • 116s cap screws (2) • 108s-2 pins (2) • 107s-2 pin (1) • Washers (3) • E-clips (3)
Prevents handlebar and front wheel from rotating or moving when the bike be stored or fixed.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
Topeak's sleek FlashStand FAT is a super parking/display stand that folds up for pocket-sized portability. This affordable, lightweight wonder securely holds your mountain bike by the non-drive side crankarm to keep it upright and safe. Take it along in your jersey pocket for those quick pit stops, too!
A 6-inch (15cm) extension that easily mounts to the main beam of any PRS-22 or PRS-22.2 to accommodate longer wheelbase bikes with bottom bracket-to-front axle lengths over 28.75 inches, including CX, gravel and enduro style bikes.
Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.
The PCS-EXT is an extension for the older pre-2001 repair stands. The kit includes a quick-release collar and extension tube to raise the working height of the stand. The PCS-EXT is required for use of the 106-AC (sold separately).
If your bike has a hollow bottom bracket, the Pro Bottom Bracket stand makes it easy and convenient to do maintenance work. This stands folds up for easy storage when not in use. - Compatible with Hollowtech 2 bottom brackets - Coated alloy - Anti-slip base
Feedback Sports repair stands are the ultimate portable and home service partner for the most demanding mechanics. They’re ultralight, compact, and durable design delivers unmatched stability, adjustability and portability. Our Travel Bag collection is an awesome travel and protective companion for ensuring your stand looks new for years to come. Be the most popular rider at the trailhead with a Feedback Sports repair stand. Be the most popular mechanic at home with a brilliant storage bag. - Maximize the portability of your Feedback Sports repair stand - Protect your stand’s aluminum finish and your other equipment when traveling - Travel bag is water-resistant, durable and padded - Enough space for a Sprint Repair Stand and a Flop Stop - External window for business cards / ID card - Padded Velcro strap for comfortable carrying and transport - Full length, dual-zipper design - Rugged end-loops for vertical storage when not in use - 1-Year Warranty
The Tilting Base fits Park's TS-2 Professional Wheel Truing Stand (sold separately). It allows adjusting the truing stand 20 degrees forward or backward for comfortable use at any bench height. The handy front bins hold Park Spoke Wrenches (sold separately) and other small items such as nipples. Rounded bin corners make even the smallest parts easy to retrieve. The base's reinforced nylon body stands up to heavy use and has holes for mounting to a workbench for stability.
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Portable Wheel Dishing Tool is a must. It disassembles quickly for storage or travel and allows you to easily check centering on road, mountain and BMX wheels from 24 to 29 inches in diameter and it works with any hub. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Topeak's FlashStand is a super work/display stand that folds up to become extremely portable as well! This affordable two-footed wonder supports your bike at the bottom bracket and down tube and raises the rear wheel with two adjustable-height feet. Take it along in the trunk of your car to dial-in your ride before your next adventure!
Designed for bikes with hollow spindle cranksets. Lift the rear wheel to mount bike on the tune-up stand in seconds for washing, display, storage and maintenance. - CLAMP HEAD: hollow spindle drive side crank - ADD FEATURE: Quick tool-free assembly - MATERIAL: Aluminum / Engineering grade polymer / Steel - MAX WEIGHT CAPACITY: 18 kg / 39.7 lb - COMPATIBILITY: Bike with hollow spindle cranksets (more than 20 mm) - SIZE (folded): 40 x 40 x 8 cm / 15.7” x 15.7” x 3.1” - SIZE (open): 40.5 x 39.5 x 38 cm / 15.9” x 15.6” x 15” - 1.8 kg / 3.97 lb
For anyone who doesn’t want to be confined to parking lots or trailheads — adventurers, racers, and garage mechanics — Küat designed the Tri-Doc for you. Tri-Doc offers an affordable way to turn your NV 2.0 into a travel stand. Reliable tri-leg design creates a stable platform for needed tune-ups or repairs. Aluminum construction finished with polished anodizing pairs perfectly with your NV 2.0. - Portable telescoping design - Quick setup - Pairs with your NV 2.0 Trail Doc - Anodized finish reflects NV 2.0 - Rubber feet offer additional stability and protection
Topeak's LineUp Stand securely holds your bike by the rear wheel for storage or display. Its spring-loaded arm automatically adjusts to fit wheels from 20-inches to 29-inches in diameter. Use it at home to store your bike, or use it to hold your pit bike at your next cross race!
A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height. - 19 tool holding holes, slots and small trays in a variety of shapes and sizes - 14-inch (35cm) magnetic tool bar - Integrated mounting holes for PTH-1 Paper Towel Holder - Phone/tablet/clipboard holder - Pen and pencil holders - Adjustable utility hook to hang wheels, parts and scales - Height adjustable - Can be installed on a fully assembled stand
Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.
- Home mechanic portable repair stand - Sturdy tubular steel design - Folding design for compact storage and mobility - Height adjustable from 36—72" (91—183cm) - V-Box clamping jaws with quick-dial closure (26.8mm+ tube diameters) - Detachable tool organizing tray - Maximum capacity: 55lb (25kg)
- Designed to be easily mounted to post, wall, bench and flat surface. - Adjustable linkage clamp allows the bike positioned at any angle. - Max load: 30 kg.
Have you ever wondered why all Feedback Sports bike repair stands have exposed frame above the clamp head? Our Pro Truing Stand is designed to sit atop all of our portable stands! The truing stand also includes a free-standing steel base and a bench-mount adapter for when you're not traveling to races and top-secret trailheads. This single-arm, precision wheel and rotor truing stand is awesome at home and excels at races, events, or adventure-riding weekends. And with the all-new Thru-Axle Adapter, it can accommodate the most common wheel sizes for quick-release or thru-axle hub designs. Use the benchtop mount for an awesome tubeless setup and tubular gluing station. - All-New Thru-Axle Adapter accommodates: 10mm, 12mm, 15mm and 20mm – up to 157mm wide hubs (SuperBoost) - Single-arm design is lightweight, portable and compatible with most wheel systems - Precision spring-loaded tip can verify lateral and radial rollout - Measurement arm includes a disc brake rotor truing slot - Steel base measures 10.25 x 8.5-inches (26.5 x 21.5cm) and 5.8lbs (2.6kg) - Bench mount measures 4 x 6-inches (10.1 x 15.2cm) - Anodized 6061 T6 aluminum construction is ultralight, corrosion resistant and incredibly durable - Can accommodate up to 29-inch wheel with tire mounted - 9mm quick-release hubs use quick-release for mounting - 12mm, 15mm and 20mm thru-axle adapter included - 3-Year Warranty
$151.12 - $187.82
After years of research and testing, Park Tool's built what they consider the best shop clamp made. It’s smooth, versatile and built to stand up to everyday shop use. • #100-3D fits the following repair stands: PRS-2, PRS-2 OS, PRS-2 OS-1, PRS-2 OS-2, PRS-3, PRS-3 OS, PRS-3 OS-1, PRS-3 OS-2, PRS-3.2-1, PRS-3.2-2, PRS-4, PRS-4 OS, PRS-4 OS-1, PRS-4OS-2, PRS-4W and PRS-33 • #100-5D fits PCS-4, PRS-7, some models of PRS-5 (with composite top tubes), and PCS-1 models manufacturer post 2002. (Note: Inspect top tube below lever for an embossed "939") • #100-25D fits PRS-25, PCS-10, PCS-11, PCS-12 (and PRS-15 with 1951-15 Adaptor Stud) • Grips nearly any tube from 7/8” to 3” (23–76mm), including aero tubes • Micro-adjustability allows perfect clamping pressure every time and prevents damage to thin-walled tubes • Long travel cam handle allows quick entry, adjustment and exit • Versatile: It grips nearly any tube including aero shaped tubing and seat posts 7/8” to 3” (23mm-76mm). Its narrow clamping jaws (2.7”/7cm) are designed to clamp securely yet fit into tight areas or on short seat posts. • Durable, replaceable jaw covers • Soft Touch saddle cradle provides a perfect spot to temporarily rest a bike by its saddle • Built to last: Powder coated, precision machined, die-cast aluminum main body parts and high quality small parts • Fast operation: Cam-actuated adjustment system for quick entry, adjustment and exit, plus handy “spinner” handle helps speed large size range adjustments
Page 1 of 3 Next page